you can make a pipe with a pen, a bottle cap and some tape unassemble the pen and make a cicular hole at the next to the wider end of the tube find a metal bottle cap and poke a bunch of holes in it with a knife or pin tape the lid over the hole in the pen (electrical tape works best) the open end can be uesd as a carb, i covered it with tape though becasue it can get hot you can alos make a good gravity bong with a knife and a 2l bottle Make a tinfiol bowl in the lid make a hole near the bottom of the bottle fill with water covering up hole near bottom put on bowl and load up light bowl and let water drain out once full of smoke, take of lid, cover up hole and shake to cool smoke, enjoy
fuck that tin foil shit thats for 14 year olds, roll joints/blunts you might think you suck at it the first time but you get better
I'm working on useing a wine bottle some tubing a soldering iron and a socet to make a convection vaporizor!!!! It seems really easy.... But I have yet to try its still in the design stages!
heres how to make a cheap vaporizer that works well First, we're going to need some things: knife duct tape or electrician's tape 2 straws or glass tubes (optional) 16 oz. bottle cap Clear 100w. lightbulb (not frosted) First, hold the lightbulb so that the black thing on the end you put into the socket is facing up. Take your knife and cut off about a half-inch from the black thing. you might want to sand off the metal edges. Next, you need to take the wire and glass parts just inside the lightbulb, so you have a glass container. Take your bottle cap and cut two holes in it, about the size for a straw to fit through. You can use tape around the neck of the lightbulb to make a handle, the glass can get hot. Rinse out the lightbulb, and screw/tape on the lid. Put the straws in, or a peice of tape over the holes, and you're ready to go! (I'd let it dry before using it) How To Use Your Vaporizer Take your weed and put it in the lightbulb. Now put your cap on, and have a lit tea-candle under the bulb. Let the candle heat up the weed, and you should see a white mist in the glass. After you think you've got enough THC out, breathe through a straw or hole. Now you'r high!!
Classic bottle bong Materials: Plastic bottle Lighter Duct tape Slider (real or made of a pen and tin foil, you can figure it out ) First you need to burn a hole about 2 inches from the bottom (depending on how long your slider is and how much water you like.) Then put a piece of tape over the hole and cut a hole in the tape so the slider fits in air tight. Fill with water appropriately, put in slider, and toke from the top of the bottle neck. Also, if you want the slider to stay in the bottle you can burn a hole where you hold it for a shotgun. Steamroller (made to conserve bud and still fuck you up) Materials: Small-Medium sized bottle 5mm ratchet set piece Duct tape Lighter Weed First you'll need to burn a hole near the top (about 3/4 of the way up the bottle) for the ratchet piece to fit into. Tape over the hole and cut a hole in the tape just big enough to hold the ratchet piece snugly. Burn a hole at the bottom for a mouth piece about 1cm diameter. put the weed into the ratchet piece, inhale through the mouth piece till the bottle is full of smoke, exhale, then remove the cap from the top of the bottle and quickly inhale the smoke from the bottle.
Ever considered produce? I don't have pictures except on my phone, but my friends have made pieces out of apples, and each time it was great, we'd put blunts in a hole and smoke the blunt through the apple. Man it ripped and tasted damn good. we've had pieces made out of pineapple and cucumbers (haha) and the best, the cream of the crop, was a watermelon bong, but the weed was in a papaya (i think). It was the coolest contraption ever...wish I could explain how to make it, but not so much
I'm going to be making a bucket (grav bong) out of a captain morgans bottle or a bombay sapphire bottle (depends which one gets finished first) by drilling several hole son the bottom with a glass drill bit. If it works out nicely I'll post a pic.
a very simple way of making a steamroller is take a toilet roll tube or a kitchen towel tube poke a hole in the side and insert a joint into said hole. to hit it you place the palm of your hand over one of the ends, you then put the other end against your mouth making a airtight seal. apply the lighter to the joint (or not if its cherried) keep inhaling until you fell it a tiny bit on the back of your throat then take your palm of the end and suck hard. lightbulb vapes dont work at all in my opinion.
EEEERRRRRRGGGGGGG!!!!!!!! no more home made pipes!!!!!!!!!!! start using glass or start rolling. homemade pipes make you look like a junkie
i smoke out of a waterfall bong...it saves me so much weed and im still fucked up. Here is what you need 1 propel/gatorade/etc. bottle 1 5 mm ratchet Lighter Weed Water Get the bottle top and burn it till the top turns soft and you can stick the ratchet through the top...let it cool and it will solidify around the ratchet piece. After that take the bottom of the bottle and burn a little opening that is just big enough so you can put your thumb over it and keep water in. I like to change bottles about every 20 bowls as it starts to smell then...but just keep the top and get the same bottle. Anyway...once you have the bottle made, put the weed in the opening of the ratchet...get to a sink fill the bottle up with water, screw on the top, light the weed, let your thumb off the opening at the bottom and you will see the smoke pull in...when the water is out, put your thumb back over the bottom to keep the smoke in...unscrew the cap and enjoy.. It takes me 4 bowls max to be baked...even off mids
Homemade precooler I made using an old pasta sauce can, a rubberband that goes around the glass joint part of the diffuser, another that goes around the lid, and 2 pieces of stride gum to seal it. Oh yeah, and sterilized surgical tubing to connect the contraption.
Get a mason jar, some tubing and a plumbing piece for a bowl. Stick the bowl far down into the jar, and ram the tubing into some kind of washer that you attach with heat resistant caulking to the lid of the jar. Make sure the bowl piece is long enough to be near the bottom of the jar and pour enough water in there to cover up some of the bowl piece but not the hose piece. Make sure it's airtight and then hit that shit. EDIT: I probably should have looked right above me before going to all the trouble of writing that out.
